-
- We Accept Visa, Master Card and Discover.
- Lakota
Carburetors
- Our "Pro Flo 1200" recast carb was patterned after the
- Lakota re worked Kohler Carter Model N or "boat carb"
- Innovators Not Imitators
- All finished carbs are flowed on our Super Flow 110
- Pro
Flo 1200 - Re Cast Carb - $425.00
- * Features an Alum Slide In Velocity Stack
- * Alky or Gas
- * 1.200 Venturi - Pro Stock
- * 1.000 Venturi - Stock Altered
- * 1.100 Venturi
- Re
Cast Carb Blank - $100.00
-
* Partially machined
* Do your own thing with a head start - Re
Cast Plain Carb Blank
- $25.00
- * You are on your own!
- Kohler
Lakota Super 1" Carb - Gas
- $250.00
- * 1.000 Venturi
- * Features an Alum Slide In Velocity Stack
-
* With your acceptable core
- Kohler
Lakota Super 1" Carb - Alky
- $258.00
- * 1.000 Venturi
- * Features a Slide In Velocity Stack
-
* With your acceptable core
- Kohler
Lakota Super 1.100 Carb - Gas
- $260.00
- * 1.100 Venturi
- * Features an Alum Slide In Velocity Stack
- * With your acceptable core
- Kohler Lakota Super 1.100 Carb - Alky - $265.00
-
- * 1.100 Venturi
- * Features an Alum Slide In Velocity Stack
- * With your acceptable core
- Velocity Stack - Slide In - $65.00
- * 1.000 - 1.100 - 1.200
- * With or Without Air Cleaner Flange
- * Carb must be machined to except velocity stack
- Kohler Flat Head Carb Core Charge - $50.00
- Lakota
Kohler
Re Worked Gas Stocker
Carb - $85.00
* On your 26mm core - 12-14 hp -
* On your 30mm core - 16 hp
-
* With your acceptable core
- Lakota
Bolt
On Velocity Stack - $45.00
* With or without air cleaner flange - * For on Stock or re worked stocker carbs
- * No Machining Needed
- Lakota 5/8" Bolt On Kohler Carb Velocity Ring - $22.00
- * No Machining Needed
- * For on Stock or re worked stocker carbs
- Lakota Carb Parts
- 1" Alum Kohler Carb Spacer - $20.00
- 3" Alum
Kohler Carb Spacer
- $40.00
- Command Bolt On Velocity Stack
- $60.00
* For on Stock Carbs - no machining needed - Onan Bolt On Velocity Stack
- $60.00
* For on Stock Carbs - no machining needed - Custom Manifolds Available - Starting at - $150.00
- * S&S and Mikuni
- Alky Brass Needle & Seat - $15.00
- Alky Brass Replacement Needle - $8.00
- Gas Performance Needle & Seat - $10.00
- Stock Needle & Seat - $9.00
- 3 Pack - Stock Needles - $9.00
- S&S Carb Jet Blank - .062 thru hole - $7.00
- Brass Main Jet
- $8.00
* .062 Gas - .078 Gas - Alky - Blank - Bottom Adjuster
- $13.00
- Wire Swivel - $1.75
- Throttle Shaft Joint - $10.50
- Throttle Shaft - $12.00
- Bronze Throttle Shaft Bushing - $3.00
- * For Kohler carbs
- Bronze Throttle Shaft Bushing - $4.00
- * For re cast carbs
- Stainless Steel Butterfly Kit - $5.00
-
* Comes with two brass screws
* 1.280 or 1.510 - Brass Butterfly Screws - set of 2 - $1.00
- Red Thread Lock
- $10.00
- Float & Pin
- $11.00
- Alum
Kohler Carb Bowl
- $9.00
- Bowl Spring - $6.00
- Bowl Ring Gasket - $3.00
- Bowl
" D" Gasket - 3
for/
- $1.00
- Brass Idle Screw - $7.00
- Kohler Block
1 1/2" Carb Stud
& Nut Kit
- $4.00
- Kohler Block
2" Carb Stud & Nut Kit
- $5.00
- * for with 1" spacer
- Intake Gasket
- .031
- $1.75
- Intake Gasket - .175 - $8.50
- Brass
Carb Fuel Inlet Fitting - 90 Degree
-
$4.00
- * 1/4" or 1/8"
- Clear Fuel Line
- 3/8"
- $0.75
* Per foot - Fuel
Line Hose Clamp - 3/8"
- $0.75
- Mr. Gasket Gas Pedal With Cable - $38.00
- Mr. Gasket Replacement Cable - $19.00
- Mr. Gasket 12 Volt Electric Fuel Pump - $41.00
- Holley Fuel Pump Replacement Spring - $4.75
Please See The Lakota Racing Command Page For All Command Part.
- We Accept Visa, Master Card and Discover.